Power Requirements 12 V DC (10.8 V to 13.2 V)
PoE++ IEEE802.3at standard: DC 42 V to 57 V (Camera Input)
Current consumption 1.0 A (Connector Input)
0.6 A (PoE+ power supply)
Ambient Operating Temperature 0 °C to 40 °C (32 °F to 104 °F)
Ambient Operating Humidity 20% to 90% (no condensation)
Storage Temperature -20 °C to 50 °C (-4 °F to 122 °F)
Weight Approx. 3.2 kg (7.05 lb)
Dimensions (W x H x D) (mm) 342 mm x 178 mm x 245 mm(excluding protrusions)
Dimensions (W x H x D) (inch) 13-15/32 inches x 7 inches x 9-21/32 inches(excluding protrusions)
Controller Supported Equipment IP/RS422
AW-UE150W/K, AW-HR140*1, AW-HE130W/K*1, AW-HN130W/K*1, AW-UE70W/K*1, AW-UN70W/K*1, AW-HE40 Series*1, AW-HN40HW/HK*1, AW-HE38HW/HK*1, AW-HN38HW/HK*1
Input/Output Connector -
INPUT DC 12 V
IN XLR 4-pin
3G-SDI IN
SMPTE292 / 75 O (BNC x 1)
Supported formats:
1080/59.94p*2, 1080/50p*2, 1080/59.94i, 1080/50i, 1080/23.98p, 1080/25p, 1080/23.98PsF, 1080/25PsF
OUTPUT ACTIVE THRU OUT
SMPTE292 / 75 O (BNC x 1)
INPUT/OUTPUT IP CONT:
100BASE-TX
PoE+ input
Connection cable: LAN cable, max. 100 m (328 ft)
- When connecting the unit via a switching hub: Straight cable or a cross cable (category 5 cable), STP (Shielded Twisted Pair) cable recommended
- When connecting the unit directly: Crossover cable (category 5 cable), STP (Shielded Twisted Pair) cable recommended
SERIAL CONT (RJ-45):
RS-422 (control signals for remote cameras), TALLY OUT
Connecting cable:
Straight cable (category 5e or better shielded cable), max. 1000 m (3280 ft)
TALLY OUT: Open collector output (negative logic)
Maximum voltage resistance DC 24 V, Maximum current 50 mA
TALLY/GPIO 1
D-sub 25-pin, female, inch thread
TALLY IN : 10 inputs (for receiving photocoupler signals)
GPI : 6 inputs (for receiving photocoupler signals)
GPIO : 5 inputs (for receiving photocoupler signals)
or 5 outputs (open collector outputs, negative logic)
·Input/output switched with menu settings
GPIO 2
D-sub 25-pin, female, inch thread
GPI : 10 inputs (for receiving photocoupler signals)
GPIO : 10 inputs (for receiving photocoupler signals) or 10 outputs (open collector outputs, negative logic)
·Input/output switched with menu settings
Reserve connectors:
2 connectors (For future expansion feature)
LCD Display 7-inch Touch Panel GUI Monitor (WVGA (800×480) )
SD Memory Card slot SDHC / SDXC Memory Card Slot x 1
Connection Specifications -
No. of Connectable Cameras 200 (IP), 5 (RS422)
No. of Camera Selection Buttons 10
No. of Camera Groups 20 (10 units per 1 group)
Memory -
Preset Memory No. of memory : presets 100
Tracing Memory No. of cameras : Cam1 to Cam10
Recording time, no. of memory settings : Maximum 5 min. total per camera, maximum of 10 settings per camera
Other Functions -
No. of User Assignable Buttons 6 + up to 10 on the LCD menu
Pan / Tilt Speed Adjustment 7 levels
Tally LED display color green / red
Note Connection with the AW-RP150GJ is planned for future support. Contact your sales representative for further information on when support will be available for this feature. Use may require a software version update. *2: Level-A support only.